Accessories for racking include all the guarding elements such as guards, barriers, decks, stops, locks, and warning signs that are used with pallet racking. Racking damage usually arises from the frequent contact by the forklift, not due to overloading, and the appropriate accessories are responsible for cushioning the impact to prevent bending of an upright or the falling of a beam.
Accessories for racking are relatively inexpensive compared to racking, but they are the determining factor for the period during which racking will remain safe to use. In this guide, the origin of racking damage, the functions of accessories, selecting accessories depending on layout, and how GENAVCO supports Godrej racking with accessories and inspections is provided.
Sources of Racking Damage
- Forklift collision: forklift trucks turning to enter aisles collide with the front uprights, mainly at the end of the aisles.
- Placement of pallets: pallets pushed too far bump the beams or even fall out of the rear end of the racking.
- Lack of lock: beams that lack locks can be lifted up when impacted from below.
- Overloading: loads exceeding the load capacity of the beams cause bending over time.
- High utilization: busy warehouses see more impacts and therefore more damage. The choice of handling equipment matters as much as the racking.
Racking Accessories and What Each One Does
| Accessory | What it does | Where it goes |
| Upright protectors and column guards | Absorb minor impacts that would deform the upright | Base of uprights in the forklift travel path |
| End-of-aisle barriers | Stop trucks hitting the end frame when turning | Ends of each run, facing the main aisle |
| Floor bollards | Protect corners and keep trucks away from vulnerable points | Aisle ends, doorways, corners |
| Beam safety locks and pins | Stop beams lifting out of connectors | Every beam connector |
| Wire mesh decks and pallet supports | Support loads that do not sit fully across beams | Levels holding small or uneven pallets |
| Pallet stops and back guards | Stop pallets being pushed through the back | Back of each level, especially near walkways |
| Row spacers | Keep back-to-back runs aligned and stable | Between back-to-back frames |
| Load signs | Show the rated capacity of each bay and level | End of each run |
Godrej Racking From GENAVCO
1. Godrej Selective Pallet Racking
- Confirmed design: the simplest and most economical racking system with 100% accessibility to each pallet, adaptable to varying pallet and load heights, with a wide range of beams and uprights.
- Confirmed compatibility: works with most material handling equipment, including forklifts, stackers and reach trucks.
- Confirmed accessories: a variety of racking accessories is available to enhance safety during pallet handling by material handling equipment.
View Godrej selective pallet racking
2. Godrej Double Deep and Drive-In Racking
- Confirmed double deep: a simple and economical system with 50% selectivity for higher density.
- Confirmed drive-in: a dense system for a few SKUs stored in volume, where trucks enter the structure, so protection and operator care matter even more. See our guide to drive-in racking.
Is your racking taking more knocks than it should?
Send us your layout, truck types and any damage you have found. We will propose accessories and an inspection plan.
How to Choose Racking Accessories
- Step 1 - Walk through the warehouse and mark areas where the trucks turn, damaged areas, and where pedestrians walk.
- Step 2 - Install vertical bumpers along all forklift travel routes and end of aisle guards along every aisle that faces a major aisle.
- Step 3 - Verify that the safety lock is installed on each and every beam.
- Step 4 - Install deck or pallet supports when the pallet does not cover the full width of the beams.
- Step 5 - Install pallet stops or back guards in places where a pushed pallet can fall into the pedestrian walkway.
- Step 6 - Post loads and train the operators on them.
Accessories must suit the racking system and be fitted to the maker's guidance. Get confirmation from GENAVCO about the Godrej accessories in your setup.
Inspection and Repair
- Awareness on a day-to-day basis: a simple process whereby any damage to the uprights is reported immediately ensures prompt identification of any damage.
- Periodic inspection: regular inspections carried out by a competent person identifies any damage which is not readily identifiable by daily users.
- Unloading and repairing: any damaged upright should be repaired before loading.
- Structural Audit: GENAVCO provides for periodic inspections, speedy parts replacement and structural audits for Godrej systems. See Godrej storage solutions.
Training Avoids Damage More Than Guards
Accesories take the beatings; training avoids them. Training of operators, aisle marking, and speed regulation help avoid impact damage throughout the entire warehouse. Guards should be used as a last resort, not a first resort.
Racking Accessories in UAE Warehouses
- High utilisation: multi-shift operations accumulate impact damage quickly, as our guide to pallet racking systems explains.
- Mixed fleets: counterbalance trucks, reach trucks and stackers all load racks differently, so allow for the largest truck.
- Rapidly changing stock profiles: new pallet sizes may require new decks or support systems that the original layout did not have.
- Coastal humidity: check your guards, bolts and anchors for signs of corrosion.
Why GENAVCO Should Be Chosen for Racking Accessories
- Godrej racking range: selective, double deep, drive-in, shuttle, very narrow aisle and cantilever systems. Read about Godrej pallet racking.
- Inspection and audit support: scheduled inspections, quick part replacements and structural audits.
- Since 1967, Juma Al Majid Company: an established supplier from UAE certified by ISO 9001.
Common Mistakes in Racking Accessories
- Only guards where there has been damage: guard all travel routes, not just the dented uprights.
- Missing beam locks: this is one of the most frequent observations on inspections.
- Repairing uprights with tape or straps: a damaged upright needs proper assessment and replacement.
- No load signs: operators cannot respect a capacity they cannot see.
- Mixing accessories from unrelated systems: parts must suit the racking they are fitted to.
Racking Accessories FAQ
What is racking accessories?
Guards, barriers, bollards, beam locks, mesh decks, pallet supports, pallet stops, row spacers and load signs fitted to pallet racking to protect the structure, stock and people.
Do I require upright guards on every rack?
Install guards where forklifts operate in the vicinity of uprights, particularly at the end of aisles and at active intersections. These protect the upright against incidental impacts which might otherwise harm it.
How frequently do I need to inspect my pallet racking system?
Combination of impact reporting every day, and inspection from time to time by a competent person, followed by immediate repair of any damage.
Does GENAVCO provide racking accessories?
GENAVCO provides Godrej racking systems, along with accessories for their selective pallet racking, and also inspection/structure audits.
Ready to Protect Your Racking?
The right racking accessories keep warehouse racking systems safe to load for longer. GENAVCO supplies Godrej racking and accessories across the UAE, with inspections and audits to match. See also our guides to industrial racking systems and racking system suppliers.
Tell us your layout and trucks. We will recommend the right accessories and price them properly.
Serving Dubai, Abu Dhabi, Sharjah, Al Ain and the wider UAE.



