A low pressure air compressor is built to deliver large volumes of air at a few bar, rather than the 7 to 10 bar a standard plant air system runs at. The Denair low pressure screw range GENAVCO supplies, for example, is designed around an operating pressure of 3 bar.
The answer lies in energy. Most plants compress all their air at full plant pressure, and then control the pressure at lower levels for processes that require just 2 or 3 bar. While this works, it makes more sense to compress air at a pressure level that will eventually be wasted by the process. This guide will help determine where it is necessary to use a low-pressure compressor, and how it stacks up against a blower.
| Key facts | Detail |
| What it is | A compressor designed to supply high air volumes at low pressure, at a few bar, such as the 3 bar Denair range |
| Where it works | Process duties that need air in volume rather than force, such as conveying and process air |
| Spec that matters most | Flow at the pressure your process needs, and the power used to make it |
| GENAVCO range | Denair low pressure screw compressors, 55 to 250 kW, 3 bar, variable speed |
What is a low pressure air compressor used for?
Any process that moves or uses a lot of air at a few bar is a candidate. Examples of such applications are pneumatic transport of powders, granulates and pellets, certain fermentation and process air operations, and blowing and drying operations on manufacturing lines. In all of these cases, the work is done by the volume of the air, not by any pressure increase.
Compressed air tools, cylinders and valves are different. They are designed for standard plant pressure, so they stay on the main air compressor system.
Why not just turn the pressure down on the plant air?
Regulating 7 bar air down to 3 bar at the point of use does not recover the energy already spent at the compressor. The machine has already used the energy to reach 7 bar. Roughly speaking, for every additional generation pressure bar, there is an estimated increase of between 6 and 8 percent to the energy consumption of the area near the plant's regular pressure point, making wrong pressure settings one of the most costly practices in a compressor room.
Adjusting the setpoint of a typical compressor does not always solve the problem too. In case some equipment within the network still requires full pressure, the entire network must be kept at a high level of pressure. Separating the low-pressure demand into another unit allows operating under different pressures for each network.
Low pressure screw, blower or standard compressor?
| Question | Blower | Low pressure screw | Standard 7 to 10 bar compressor |
| Usual pressure range | Mostly below about 1 bar | A few bar; the Denair range runs at 3 bar | 7 to 10 bar for plant air |
| Best for | Aeration and very low pressure duties | Conveying and process air at a few bar | Tools, cylinders and general plant air |
| Energy on a 3 bar duty | Not suited above its range | Efficient, because it compresses only as far as needed | Wasteful if the air is regulated down |
| Typical set-up | Dedicated to one process | Dedicated low pressure network | Shared plant network |
For a wider view of the options, our guide to compressor types covers screw, oil-free, portable and centrifugal machines, and our screw compressor guide explains how screw elements work.
What should you check before you buy one?
- Real pressure at the point of use. Measure what the process needs at the machine, then add the pressure drop across pipework, dryers and filters.
- Flow over a full week. Log consumption across shifts, because a single reading hides the peaks and troughs that decide machine size.
- How much demand you can separate. Map which users can move to a low pressure network and which must stay on plant air.
- Air quality. If the air touches product, confirm the quality class you need and whether oil-free compression is required. The Denair low pressure range is not listed as oil-free, so confirm this for product contact duties.
- Fixed or variable speed. Demand that rises and falls through the day usually suits variable speed control.
- Plant room conditions. Hot UAE plant rooms reduce output and stress components, so plan ventilation and cooling from the start.
- Parts and service. Check that filters, oil, service kits and technicians are available locally.
Which GENAVCO models fit?
GENAVCO supplies the Denair range, so a plant can split its demand across machines designed for each pressure.
| Denair Low Pressure Screw Air Compressors | |
| Motor power: 55 to 250 kW (75 to 350 hp)
Operating pressure: 3 bar Control: variable speed Components: SAP profile screw element, Schneider electronics, Danfoss pressure sensor and SKF bearings Controls: intelligent controller with multi-language LCD screen Standards: CE and ISO 9001 |
|
| Best for: Plants with a large, regular need for air at around 3 bar | |
| Denair Electric Screw Air Compressors | |
| Motor power: 5.5 to 400 kW
Free air delivery: 0.36 to 74.49 m3/min (12 to 2,630 cfm) Control: fixed speed or variable speed |
|
| Best for: The standard pressure network that runs tools and general plant air | |
Send us your process pressure, flow profile and air quality needs and we will size the right machine. You can request a compressor quote or see the full range of Denair compressors.
What does a low pressure compressor cost to run and maintain?
Electricity is usually the largest cost over a compressor's life, as our guide to running costs explains. A low pressure machine attacks that cost directly, because it does less compression work for the same volume of air.
- Variable speed: speed adjusted according to the requirement, which would ensure that you don’t need to run the motor at its maximum capacity.
- Leakages: the lower system pressure would mean that there is less air loss from any leakage, but they will always waste money.
- Filters and coolers: dust and high temperatures during summers affect the intake filters and coolers in the UAE more rapidly.
- Scheduled maintenance: proper change of oil, filters and separators will maintain your energy consumption levels.
GENAVCO supports Denair compressors with genuine parts, preventative maintenance and on-site service across the UAE.
Common questions
What pressure does a low pressure air compressor work at?
Usually a few bar. The Denair low pressure screw range GENAVCO supplies operates at 3 bar, compared with the 7 to 10 bar typical of plant air.
Is a low pressure compressor the same as a blower?
Not quite. Blowers mostly serve duties below about 1 bar, such as aeration. A low pressure screw compressor covers the gap between a blower and a standard compressor.
Can I use my existing compressor at a lower setting?
You can lower the setpoint if every user on the network accepts it. If tools still need full pressure, a separate low pressure machine for the process duty is usually the more efficient answer.
Are Denair low pressure compressors available with variable speed?
Yes. GENAVCO lists the Denair low pressure screw range in variable speed configurations, from 55 to 250 kW.
Do I still need a dryer on a low pressure system?
This will depend on the process. If moisture would affect the product or the conveyor system, then include drying and filtering in the specification.
Tell us your process pressure and flow, and we will recommend the right low pressure air compressor.
Serving Dubai, Abu Dhabi, Sharjah, Al Ain and the wider UAE.



