Prime coat vs tack coat is simply about the position of the bitumen in relation to the aggregate. Prime coat is applied on the compacted granular base prior to application of the first layer of asphalt. Tack coat, on the other hand, is a bond coat applied between asphalt courses or on the existing pavement prior to an overlay. Both use the same spray equipment but serve different purposes.
In the case of UAE roads and parking lot construction, the application of both coatings is dictated by the client/road authority. Correct application and uniformity of the spray will determine the success of the bond between the new asphalt and the existing one.
| Key facts | Detail |
| Prime coat | Sprayed on a compacted granular substrate to seal, bond, and prepare it for the overlay of asphalt |
| Tack coat | Thin coating between layers of asphalt, or on old asphalt/concrete, to ensure bonding of the new layer |
| Typical binders | Cutback or emulsion primers for prime; bitumen emulsion is common for tack, as specified |
| GENAVCO equipment | Weiro HK 1000 PM tank sprayer for cold liquid road binders, surface dressing and tack coating |
What is the difference between a prime coat and a tack coat?
The prime coat operates on unbound aggregate material. The liquid penetrates to a certain degree into the upper layers of the base and seals up the dust and loose aggregate material, creating a strong sealed surface on which the first layer of asphalt can be applied. The tack coat is used on bound surfaces. There is no penetration required here; there is bonding required.
| Question | Prime coat | Tack coat |
| Where it goes | On compacted granular base or sub-base | Between asphalt layers, or on old asphalt or concrete |
| Main job | Seal, bind and waterproof the base surface | Bond layers so they act as one |
| Typical binder | Cutback or emulsion primer, as specified | Bitumen emulsion, as specified |
| Before paving | Allow time to penetrate and cure | Let the emulsion break, turning from brown to black |
| Common faults | Too little penetration, ponding, traffic picking it up | Patchy cover, too much binder, dust under the film |
The spray rates and the materials to be used are determined by the specification of the project and the standard of the local road authority. Our guide to uniform bitumen spraying explains why the thin film does so much structural work.
How can the two coats be significant to road life?
- Bonding: Without a good tack coat, layers will shift on top of one another during braking and turning movements of vehicles and the upper layer may crack or peel.
- Base Protection: With a good prime coat, the base becomes watertight and helps in keeping the base fines intact until the upper layer is paved.
- Over application: Excess use of tack coat may act as a slip plane or may ooze to the surface through a thin layer of pavement.
- Contamination: Dust, sand and tire pick-up between coating and paving disrupt the bonding action before the arrival of asphalt.
What should be checked before spraying?
- Specification. Check the type of binder to be used, the rate of application and the curing or breaking period for each layer.
- Surface. Clean the base or old asphalt of any dust or sand. The tack coat requires a dry surface while for the prime coat a light water spray to a dry surface is recommended by some specifications.
- Weather and Timing. Warm weather accelerates breaking/curing while wind causes dust and overspray. Night spraying will reduce curing speed and requires lighting of the area.
- Binder heating. Heat the binder to the required temperature so that it can flow well through the nozzles.
- Adjustment of spray bar. Adjust the spray bar height and nozzle angle so that the fan pattern overlaps as intended and all the nozzles spray well.
- Calibration. Test the actual spray rate on a small test area compared to the required one before the major operation.
- Traffic control. Prevent any traffic from using areas just sprayed to avoid the binder being picked up by their tyres.
How does a bitumen spray tanker do so evenly?
Bitumen spray tanker holds the binder within a heat-insulated tank, maintains it at an operational temperature, transfers it to a spray bar for circulation and dispenses it in overlapping fans as the vehicle is driven at a constant speed. Evenness of coverage depends upon all these factors operating in harmony with each other. Our guide to bitumen spray tankers in the UAE covers tank size; heating and mounting in more depth.
GENAVCO equipment which applies?
Weiro bitumen sprayers are produced by GENAVCO and are manufactured in Germany by Weisig Maschinenbau, a family-owned business for three generations.
| Weiro HK 1000 PM Tank Sprayer | |
| Binders: cold liquid road binders for surface dressing and tack coating
Tank: insulated welded steel, different capacities, on a rigid sub frame Spray bar: full circulation with two foldable extensions, approx 4.0 m spray width Controls: electro-pneumatic open and close from the driver's cabin Heating: fuel burner with electronic thermostat |
|
| Best for: Contractors running tack coat and surface dressing work who want a sprayer on a local truck | |
Its modularity enables it to be installed on any locally available truck chassis. In case you want to coat using this machine with a certain binder, please inform us about the binder to be used. Send your binder types and daily spraying area to request a spray tanker quote.
How expensive is it to keep up spraying operations?
Binder constitutes the greatest expense on most sites, so any amount of application makes sense. Equipment practices come to a few things.
- Purge system after each use: blow out the binder circuit and spray bar after each use to prevent binder from setting up in the circuit.
- Maintain nozzles: clean nozzles that have become blocked and/or worn. One malfunctioning nozzle will result in a “stripe” either lean or heavy down the lane.
- Heating system/burner: have the heating system serviced to ensure binder stays at a constant temperature.
- Storage tank and binder pump: inspect tank and pump for wear and leaks.
Spraying is one step in a chain that runs from the asphalt plant to the asphalt paver, and delays at any step affect the coat waiting on the road.
Common queries
Is it possible not to apply the tack coat to the new layer of asphalt?
Only if allowed in the specification. Freshly applied asphalt may attract dust, and the tack coat serves as a binder between the layers.
How long does the primer coat need to cure before the pavement application?
Depends on the type of the binder and the ambient temperature. Follow the recommendation in the specification and keep the traffic away from the area during that period.
What does it mean if a tack coat is broken?
In case the emulsion is broken, the separation occurs, leaving only the bitumen behind which turns the color of the emulsion from brown to black.
Is it possible to have one spray tanker for priming and tack coats?
Yes, if the tanker is able to handle both types of binder, its rate can be adjusted for both and the tank and lines are cleaned before the changeover. Verify the binders from your supplier.
What is the spray width for the Weiro HK 1000 PM?
GENAVCO states a complete circulation system with two fold out extensions, with a spray width of about 4.0m.
Let us know your binders, sprayed areas and truck requirements, and we will suggest the ideal spray tank assembly.
Serving Dubai, Abu Dhabi, Sharjah, Al Ain and the wider UAE.



