An industrial vacuum pump evacuates air and processes gas from a closed vessel or line in order to be able to perform a process below atmospheric pressure. The dry screw vacuum pump evacuates this gas using two rotors running in mesh with each other, without any oil or water in the pumping chamber, thereby keeping the process gas clean and avoiding contamination by oil or wastewater.
Type vacuum pump into UAE search engines and you get a list full of small HVAC service pumps. This is not what we are talking about in this guide; we will discuss process vacuum for factories. In addition, you will learn more about vacuum levels and pumping speeds, comparison of dry screw, oil-sealed and liquid ring pumps, and Denair screw vacuum pump GENAVCO.
What’s the Difference between a Vacuum Pump and a Compressor?
The compressor forces the air into the system with pressure above the atmospheric pressure, for performing processes. The vacuum pump takes the gas from the closed volume and expels it to the atmosphere. Many plants need both, and they are often specified by the same engineer. For the compressed air side, see our guide to compressor types compared.
The Two Numbers that Define a Vacuum Pump
- Ultimate pressure: the pressure the pump can achieve when its inlet is shut. The lower the number, the deeper the vacuum. Units are either mbar or Pa, where 1 mbar = 100 Pa.
- Pumping speed: the amount of gas the pump removes in an hour from its inlet, measured in m3/h. Determines how fast the vacuum chamber will be emptied and how well the pump copes with gas that is being emitted.
Both depend on the process. In the packaging process, one may require a moderate vacuum, but a high pumping speed. In drying or degassing processes, there could be requirements of deep vacuum maintained for long intervals of time.
Dry Screw vs Oil-Sealed vs Liquid Ring Vacuum Pumps
| Factor | Dry screw | Oil-sealed rotary | Liquid ring |
| Sealing medium in chamber | None | Oil | Water or another liquid |
| Risk of contaminating process gas | Very low | Oil vapour can reach the process | Liquid vapour present |
| Waste stream | None from the sealing medium | Used oil and oil mist | Contaminated sealing liquid |
| Tolerance of vapours and particles | Good, with suitable clearances | Oil degrades with vapours | Good with wet gases |
| Routine maintenance | Low | Regular oil changes | Liquid management |
The comparison above is a general guide. The right choice depends on the gas being pumped, so share the process details before fixing a technology.
The Denair Screw Vacuum Pump Available in the UAE
1. Denair Dry Screw Vacuum Pump (180 to 720 m3/h)
- Specified pumping speed range is 180 to 720 m3/h. The lowest ultimate pressure indicated by Denair's specification list is 0.6 Pa (0.006 mbar); specify the value for the particular model.
- Specified design characteristics: the shortest gas pathway for dry vacuum pumps, thus decreasing the contamination of the process gas; special rotor design featuring tight seal and higher clearance, minimizing rotor wearing and jamming caused by the process contamination; balancing of rotors on the level of G1 for low vibration.
- Specified controls: microprocessor controller indicating operational parameters, local control through an operation panel, and remote control with monitoring software.
- Cleanability: removable muffler, reducing the noise level and easy to disassemble and wash.
Specifying vacuum for a new line or replacing an old pump?
Send us the working pressure, chamber volume, cycle time and the gas or vapour involved. Our team will check whether a Denair dry screw pump fits and size it.
Where Dry Screw Vacuum Pumps Are Typically Applied
- Foods & Packaging Industries: Vacuum packing & conveying where presence of oil vapor close to product is not acceptable. The same logic drives oil-free compressors on the compressed air side.
- Plastics and rubber: degassing and moulding processes that release vapour and fine particles.
- Chemical and pharmaceutical processing: drying, distillation and solvent recovery where the pumped gas must stay clean.
- General manufacturing: vacuum holding, forming and central vacuum systems serving several machines.
How to Select an Industrial Vacuum Pump
Step 1 - State the required operating pressure and the speed at which it should be achieved.
Step 2 - State the volume of the chamber or system being used, including piping.
Step 3 - State the gases or vapours involved, their particle size, if present, and their temperature entering the pump.
Step 4 - State the pump's duty; whether it is continuous, cyclic or intermittent.
Step 5 - State the location of the pump and the means of disposing of exhaust gas and heat.
Step 6 - Request performance at your required operating pressure.
Vacuum Pumps at UAE Plants
- Heat in plant rooms: due to high outside temperature, the specification will include ventilation and cooling of the pump room.
- UAE Industrial Strategy: called Operation 300bn, the strategy envisages an increase in the share of industry in GDP from AED 133 billion to AED 300 billion by 2031, implying the need for more processing facilities and hence more process vacuum.
- Dust in intake air: maintain cleanliness in the area of the pump and provide for filtration of dust, which may get into the process with intake air.
- Remote control: multiple-site operators appreciate controllers informing on the running status of the pump remotely.
Why Choose GENAVCO for Vacuum Pumps
- Denair compressed air and vacuum from one supplier: compressors, dryers, filters and vacuum pumps specified as one system. See Denair compressed air and vacuum.
- Part of the Juma Al Majid Group since 1967: an established UAE supplier with ISO 9001 certification.
- Service and genuine parts: certified technicians and genuine parts support the pump after commissioning. For the wider range, read the full Denair range.
Common Vacuum Pump Mistakes
- Buying on ultimate pressure alone: pumping speed at the working pressure decides whether the process keeps up.
- Ignoring what is in the gas: vapours and particles change which technology will last.
- Undersizing pipework: long, narrow lines reduce the speed delivered at the process.
- Placing the pump in a hot, closed room: heat shortens the life of any pump.
FAQs
What is the use of an industrial vacuum pump?
The removal of air or gas from a closed chamber or pipeline to allow the process to occur below atmospheric pressure. Common applications of this device are found in the processes of packaging, degassing, drying, distillation, molding, and vacuum retention in industry.
What is a dry screw vacuum pump?
A vacuum pump which uses two meshed screw rotors without any oil or water inside the vacuum pump chamber. Since nothing seals the chamber, the gas remains free of contaminants and no oil is discharged from the system.
How low is the vacuum that Denair screw vacuum pump can achieve?
The lowest possible pressure achieved by Denair screw vacuum pumps is 0.6 Pa, which is 0.006 mbar, with flow rates ranging between 180 and 720 m3/h. The specific number should be verified for your application.
What price does an industrial vacuum pump have?
Price is determined by the pumping speed, vacuum level, material that fits the process gas, and controls. Specify your working pressure and process conditions for an accurate quotation.
Ready for Your Vacuum Pump Specifications?
The appropriate vacuum pump will be selected based on the pressure in your system and the gas you are processing. GENAVCO supplies the Denair dry screw vacuum pump across the UAE, alongside the Denair compressor range in our air compressor buying guide.
Tell us your working pressure, volume and process gas. We will size the pump and price it properly.
Serving Dubai, Abu Dhabi, Sharjah and the wider UAE.



