Gear oil lubricates the gears and bearings in axles, differentials, and manual transmissions to prevent wear under high loading conditions. Gear oil selection boils down to two things - API Service Classification GL-4 or GL-5, and SAE Viscosity 80W-90, 90 or 140. Both need to be compatible with manufacturer specifications.
Making a mistake with either one is easy since gear oils come in similar looking packages with similar numbers. This guide describes what GL-4 and GL-5 classifications are, gear oil viscosity numbers, the application of gear oil for trucks and other machinery, and BP Energear range of GENAVCO.
For What is Gear Oil Used?
- Differential gears and final drive gears: Hypoid gears within axle are sliding as well as rotating, resulting in high loads on gear surfaces.
- Manual transmissions: Gear sets and synchronizers that require lubrication without interfering with gear shifting.
- Gear units of industrial machinery: Spur gears, bevel gears, and helical gears of construction and agricultural machines.
Automatic transmissions are a separate case. They usually take automatic transmission fluid (ATF), not gear oil. See our article on automatic transmission maintenance.
GL-4 vs GL-5: What Is the Difference?
API service classes describe how much extreme pressure (EP) protection a gear oil carries. GL-5 contains more EP additive and is designed for hypoid gears in differentials and axles under severe load. GL-4 carries less and is the usual specification for many manual gearboxes and transaxles.
| Factor | API GL-4 | API GL-5 |
| Extreme pressure additive level | Moderate | High |
| Typical use | Manual gearboxes, transaxles, spur and helical gears | Hypoid differentials and heavily loaded axles |
| Using it in the other application | Too little protection in a hypoid axle | Can affect synchronisers in some gearboxes that specify GL-4 |
| BP Energear example | Energear 90, Energear 140 | Energear Axle 80W-90 |
The best practice is straightforward: follow the class as stated by the manufacturer. Beware of assuming that the larger number is the superior choice.
Gear Oil and Engine Oil Numbers Are Different Scales
An oil that is classified as 90 cannot be compared to an oil that is 40 or 50. The reason behind this is that gear oils and engine oils have two different SAE viscosity classification schemes; thus, their classification applies to gear oils only. In relation to gear oils, the multigrade of 80W-90 flows better in comparison to the monograde of 90 but with protection similar to 90 in terms of heat resistance.
The BP Energear Range From GENAVCO
1. BP Energear Axle 80W-90 (API GL-5)
- Confirmed application: multigrade gear oil for differentials, transaxles and transmissions of trucks, light commercial vehicles and passenger cars requiring API GL-5.
- Confirmed advantages: high load carrying capability for gears under high loads, and better cold start fluidity than a monograde 140.
2. BP Energear 90 (API GL-4)
- Confirmed application: manual transmission fluid for applications that require API GL-4 performance.
- Confirmed advantages: good thermal stability against deposits and oil thickening, and good anti-wear and load carrying characteristics.
3. BP Energear 140 (API GL-4)
- Confirmed application: a wide range of gear units with spur, bevel or helical gears, including synchronised manual gearboxes, in passenger cars, light and heavy trucks, agricultural and building machinery.
- Confirmed advantages: high safety margin against foaming and corrosion, compatibility with all seal and metal types, and effective protection of gear transmissions.
Running a mixed fleet of trucks and machines?
Send us the makes and models in your fleet. Our lubricants team will map each axle and gearbox to the right BP Energear grade.
REQUEST A LUBRICANT RECOMMENDATION
Gear Oil, Hydraulic Oil, And ATF Are Not Interchangeable
- Gear Oil: axles, differentials, and manual gearboxes, using EP additives to protect teeth.
- Hydraulic Oil: hydraulic system, using anti-wear additives for pumps and valves.
- ATF: automatic transmissions and many power steering systems. BP Autran Dex/Merc is designed for Dexron IIIH or Mercon applications and can also be used as power steering fluid.
One of the most common and expensive mistakes made in the workshop is the incorrect use of fluids in these systems.
Gear Oil Change Interval?
- Check your owner’s manual for the recommended gear oil change interval. In severe conditions where there is heavy load, long climbs, excessive temperatures, or dusty operating environment, the shorter gear oil change interval will normally apply. You should check earlier if you observe:
- Whining or squeaking from the axle or gearbox.
- Leakage from seals, breathers, or the axle housing.
- Presence of metal particles in the drain plug magnet at each oil change.
- Notchy or hard shifting in the manual gearbox.
Selecting the Appropriate Gear Oil
Step 1 – Identify the type of gear oil used by the manufacturer according to API class (GL-4 or GL-5).
Step 2 - Identify the SAE gear oil viscosity grade like 80W-90, 90 or 140.
Step 3 - Identify any approval by the manufacturer in the manual.
Step 4 – Tag fill points and store so that the axle and gearbox oils do not get interchanged.
Step 5 - Set intervals for the actual duty, not the lightest one in the manual.
Gear Oil for UAE Conditions
- Temperature: Long summers lead to high temperatures within the axles; hence, there is a need for high oxidation resistance and proper viscosity.
- Dust: Fine sand may get into the system through the breathers and damaged seals; therefore, ensure to check them at every service period.
- Fleet Mix: Construction and logistics fleets are usually made up of equipment from Europe, Asia, and America. A simple grade map prevents mistakes.
- Long service intervals cost more than oil: a failed differential costs far more than the oil that would have protected it. See how this feeds into total cost of ownership.
Why Choose GENAVCO for Gear Oil
- Genuine BP lubricants: GENAVCO's lubricants division supplies gear, hydraulic and engine oils, transmission fluids and greases. See GENAVCO lubricants.
- Drivetrain knowledge: GENAVCO also represents Allison automatic transmissions and services the equipment it supplies.
- Part of the Juma Al Majid Group since 1967: an established UAE supplier with ISO 9001 certification.
Common Mistakes in Choosing Gear Oil
- GL-5 for all gearboxes: GL-4 is used in some boxes because of its specific properties.
- GL-4 in hypoid gearboxes: does not provide enough lubrication under heavy load.
- Gear oil API numbers versus engine oil API numbers: they are different.
- Filling an automatic transmission with gear oil: automatic transmissions use ATF.
- Ignoring the drain plug: metal on the magnet is an early warning worth acting on. Efficient drivetrains depend on it, as our article on powertrain efficiency in heavy equipment explains.
Frequently Asked Questions
How is gear oil used?
Gear oil is meant for lubrication and protection of gears and bearings within differentials, axles, final drives, and manual transmissions where the tooth loading is extremely high.
What is the difference between GL-4 and GL-5 gear oil?
GL-5 has a more extreme pressure additive and is meant for hypoid differentials and highly loaded axles. GL-4 has less of an extreme pressure additive and is usually specified for use in manual transmissions.
Is 80W-90 the same as 90 gear oil?
Not exactly. Both provide protection equal to a 90 once they get warm, but the 80W-90 is multi-viscosity and starts off thinner. BP Energear Axle 80W-90 also features an API GL-5 rating, but Energear 90 is API GL-4.
How do you know when to change gear oil?
At the specified interval as listed in your manual, based on severe service intervals for heavy loading, high heat, or dusty conditions. Look for warning signs such as whining, leaks, or metal shavings on the drain plug.
Choosing Gear Oil for Your Vehicle?
API Classification and Viscosity Should Be Specific to Each Axle and Gearbox; Also, Gear Oil, Hydraulic Oil, and ATF Should Be Separated Properly. GENAVCO supplies the BP Energear range and the wider BP lubricants line across the UAE.
Tell us your vehicles and machines. We will recommend the right gear oils and price them properly.
Serving Dubai, Abu Dhabi, Sharjah, Al Ain and the wider UAE.



